Browsing by Subject "Resilient modulus"

Now showing 1 - 4 of 4
  • Thumbnail Image
    Item
    Cone Penetration Testing in Pavement Design
    (Minnesota Department of Transportation, 2007-09) Dehler, William; Labuz, Joseph
    The objective of this work was to show that cone penetration testing (CPT) can be used for pavement applications, specifically estimating resilient modulus and organic content. A series of undisturbed samples were obtained from borings directly adjacent to CPT soundings. These samples underwent both laboratory resilient modulus and bender element testing. A statistical analysis was then performed on these results in conjunction with the data obtained from the CPT soundings to determine the feasibility of developing correlations between field and laboratory measurements of moduli. A relationship was developed between Young's modulus determined by bender element testing and that determined by resilient modulus testing. However, the correlation did not apply to the field-based seismic measurements of stiffness from the CPT soundings. The analysis presented with respect to the identification of highly organic soils via CPT testing shows that at this point the model identified using the discriminate analysis method is not currently sufficient to use in practice. The 10% increase in correctly classified soils, however, holds promise for the future, and the introduction of additional independent parameters within a significantly larger data set can be easily analyzed using the methods and tools presented here.
  • Thumbnail Image
    Item
    Pavement Design Using Unsaturated Soil Technology
    (Minnesota Department of Transportation, Research Services Section, 2007-05) Gupta, Satish; Ranaivoson, Andry; Edil, Tuncer; Benson, Craig; Sawangsuriya, Auckpath
    Pavements are constructed on compacted soils that are typically unsaturated. The negative pore-water pressure (soil suction) due to the ingress of water in between soil particles has a significant effect on pavement foundation stiffness and strength. The study characterized the effects of soil suction on shear strength and resilient modulus of four soils representing different regions of Minnesota. The deviator stress in shear strength measurements followed a power function relationship with soil suction. Resilient modulus also followed the power function relationship with suction but these relationships fell within a narrow range. We present models for incorporating suction effects in shear strength and resilient modulus measurements of highly compacted subgrade soils. We also briefly outline a framework for incorporating these models in the resistance factors of MnPAVE. Since soil water content and the resulting soil suction under the pavement varies with season, adjustments are needed to account for increased strength and stiffness of the material as a result of unsaturated soil conditions. These adjustments will not only reflect the more realistic field conditions but will result in more reliable performance predictions than the current pavement design method.
  • Thumbnail Image
    Item
    Resilient Modulus And Strength Of Base Course With Recycled Bituminous Material
    (Minnesota Department of Transportation, Research Services Section, 2007-01) Kim, Woosung; Labuz, Joseph
    The objective of the research was to determine the strength and deformation characteristics of base material produced from recycled asphalt pavement (RAP) and aggregate. Various samples with different ratios of RAP and aggregate base were mixed (% RAP/aggregate): 0/100, 25/75, 50/50, 75/25. Laboratory compaction testing and field monitoring indicated that gyratory compacted specimens were closer to the densities measured in the field. Resilient modulus (MR) tests were generally conducted following the National Cooperative Highway Research Program 1-28A test protocol. MR increased with increase of confining pressure, but MR showed little change with deviator stress. The specimens with 65% optimum moisture contents were stiffer than the specimens with 100% optimum moisture contents at all confining pressures. Cyclic triaxial tests were conducted at two deviator stresses, 35% and 50% of the estimated peak stress, to evaluate recoverable and permanent deformation behavior from initial loading to 5000 cycles. The specimens with RAP exhibited at least two times greater permanent deformation than the 100% aggregate material. As %RAP increased, more permanent deformation occurred. In summary, the base material produced with various %RAP content performed at a similar level to 100% aggregate in terms of MR and strength when properly compacted.
  • Thumbnail Image
    Item
    Resilient Modulus Development of Aggregate Base and Subbase Containing Recycled Bituminous and Concrete for 2002 Design Guide and Mn/Pave Pavement Design
    (Minnesota Department of Transportation, 2007-06) Westover, Thomas; Labuz, Joseph; Guzina, Bojan
    The primary objective of this study was to quantify stiffness (resilient modulus) of aggregate base containing recycled asphalt and concrete pavements. After a survey of other state's specifications and implementation guidelines, Minnesota recycling projects were selected based on the availability of laboratory resilient modulus (MR) tests and field measurements from FWD. The projects were County State Aid Highway 3, Trunk Highway 23 and Trunk Highway 200. Based on the results of a parametric study, it was found that traditional peak-based analysis of FWD data can lead to significant errors in elastostatic backcalculation. A procedure for extracting the static response of the pavement was formulated and implemented in a software package called GopherCalc. Laboratory resilient modulus measurements were compared with moduli backcalculated from the FWD data. The FWD data was analyzed using conventional (peak-based) and modified (FRF-based) elastostatic backcalculation (Evercalc) as well as a simplified mechanistic empirical model called Yonapave. Laboratory values from sequences in the MR protocol that produced a similar state-of-stress were used. Additionally, a seasonal analysis of FWD test data revealed a significant increase in stiffness when the pavement is in the frozen state.