This README file was updated on 2023-09-14 by Margaret Kumler. ------------------- GENERAL INFORMATION ------------------- Title of Dataset: Supporting Data for High Performance Star Block Aliphatic Polyester Thermoplastic Elastomers using PDLA-b-PLLA Stereoblock Hard Domains Author Information: Principal Investigator Contact Information Name: Marc A. Hillmyer Institution: University of Minnesota Address: Department of Chemistry, 207 Pleasant St SE, Minneapolis, MN 55455 Email: hillmyer@umn.edu Co-investigator Contact information Name: Stephanie Liffland Institution: University of Minnesota Address: Department of Chemistry Email: liffl001@umn.edu Co-investigator Contact Information Name: Margaret Kumler Institution: University of Minnesota Address: Department of Chemistry Email: kumle007@umn.edu Date of data collection: (February 2022 – August 2023) Geographic location of data collection: University of Minnesota Information about funding sources that supported the collection of the data: This research was supported by a grant from the National Science Foundation through the Center for Sustainable Polymers (grant CHE-1901635). -------------------------- SHARING/ACCESS INFORMATION -------------------------- 1. Licenses/restrictions placed on the data: CC0 2. Links to publications that cite or use the data: https://doi.org/10.1021/acsmacrolett.3c00437 3. Links to other publicly accessible locations of the data: 4. Links/relationships to ancillary data sets: 5. Was data derived from another source? 6. Recommended citation for the data: Liffland, Stephanie; Kumler, Margaret; Hillmyer, Marc A.. (2023). Supporting Data for High Performance Star Block Aliphatic Polyester Thermoplastic Elastomers using PDLA-b-PLLA Stereoblock Hard Domains. Retrieved from the Data Repository for the University of Minnesota, https://hdl.handle.net/11299/256423. --------------------- DATA & FILE OVERVIEW --------------------- Purpose Statement: These files contain primary data along with associated output from instrumentation supporting all results reported in “High Performance Star Block Aliphatic Polyester Thermoplastic Elastomers using PDLA-b-PLLA Stereoblock Hard Domains. General Notes: Filenames are labeled as follows: “Figure in which data appears_Characterization Method_Sample ID_Other pertinent information”. For example, “Fig4_SRA_DLM.1.1_60C” refers to the data SRA analysis shown in Figure 4 for sample DLM-1:1 at 60 C. Files Contained: The data tree below includes the following raw data: Dynamic mechanical thermal analyses (DMTA), differential scanning calorimetry (DSC), proton nuclear magnetic resonance spectroscopy (NMR), small angle X-ray scattering (SAXS), size exclusion chromatography (SEC), stress relaxation analyses (SRA), tensile testing analyses, and wide-angle X-ray scattering (WAXS). Additionally, the ChemDraw images that appear in the manuscript are included. Raw NMR data files can be accessed using MNova software. All other files can be opened using a spreadsheet editor such as Microsoft Excel. Relationship between files: Additional related data collected that was not included in the current data package: None Are there multiple versions of the dataset? N -------------------------- METHODOLOGICAL INFORMATION -------------------------- Description of methods used for collection, generation, and processing of data: Bruker Avance III HD 500 was used for 1H and 13C NMR spectroscopy, and molar masses were calculated using end-group analysis. General NMR parameters are as follows: solvent: Chloroform-D, number of scans (ns): 32, relaxation delay (d1): 10s. The average molar mass values and molar mass distributions were analyzed by SEC using an HFIP mobile phase on an EcoSEC system HLC-8240GPC series liquid chromatograph through two Tosoh TSKgel SuperAWM-H columns at 40 °C and a flow rate of 0.35 mL min–1 and equipped with a refractive index detector. Molar masses and dispersities were determined by conventional calibration against poly(methyl methacrylate) (PMMA) standards. Thermal properties were obtained by differential scanning calorimetry (DSC) measurements using a TA Instruments Discovery Series differential scanning calorimeter equipped with a liquid nitrogen cooling accessory. All samples (ca. 4–9 mg) were analyzed under a nitrogen atmosphere in hermetically sealed T-Zero aluminum pans. Samples were first heated to 240 °C at 10 °C min-1 and held for one minute to erase any thermal history (first heat cycle). The samples were then cooled to –80 °C at 10 °C min-1, followed by heating to 240 °C at the same rate (second heat cycle). All reported data was collected from the second heating cycle unless otherwise indicated. Polymers were melt-pressed between two Teflon sheets in a Wabash Hydraulic Press at 215 °C. The materials were pressed at 300 lbs. pressure for 2 min and at 3300 lbs. pressure for an additional 2 minutes before being rapidly quenched (~35 °C min–1) to room temperature using water cooling. Dog-bone-shaped tensile bars were punched out after the films were allowed to rest at RT for a minimum of 48 h, resulting in samples with approximately 0.5 mm thickness, 2.5 mm gauge width, and 14 mm gauge length. Tensile testing experiments were conducted using a Shimadzu Autograph AGS-X Tensile Tester and an extension rate of 50 mm min–1 until material failure. Extensional dynamic mechanical thermal analysis (DMTA) and stress relaxation experiments were performed on a TA Instruments RSA-G2 in tension mode on rectangular polymer films with 0.5 mm thickness and ~2.0 mm gauge width. Temperature control was achieved using a nitrogen atmosphere. DMTA experiments were conducted with an oscillatory strain of 0.1% and angular frequency of 1 Hz at a heating rate of 5 °C min–1. For stress relaxation experiments, samples were equilibrated at the desired temperature for 10 min before application of a 25% step strain, and the modulus was measured for 104 s (3 h). The results of the stress relaxation studies were normalized for comparison across trials. SAXS and WAXS experiments were conducted at the DuPont-Northwestern Dow Collaborative Access Team (DND-CAT) synchrotron research center Sector 5-ID-D of the Advanced Photon Source at the Argonne National Laboratory. People involved with sample collection, processing, analysis and/or submission: Liffland, Stephanie: Data collection, processing, analysis Kumler, Margaret: Data collection, processing, analysis Hillmyer, Marc: Data analysis, submission ------------------- DATA TREE ------------------- C:. | Fig1ChemDraw.jpg | README.docx | TOCFigChemDraw.jpg | +---Raw_DMTA | Fig2_DMTA_DLM.1.1.xls | Fig2_DMTA_DLM.1.2.xls | Fig2_DMTA_DLM.2.1.xls | Fig2_DMTA_DLM.3.1.xls | Fig2_DMTA_LM.0.1.xls | FigS10_DMTA_DLM.1.1.xls | +---Raw_DSC | | Fig2_DSC_DLM.1.1_HCH.xls | | Fig2_DSC_DLM.1.2_HCH.xls | | Fig2_DSC_DLM.2.1_HCH.xls | | Fig2_DSC_DLM.3.1_HCH.xls | | Fig2_DSC_LM.0.1_HCH.xls | | | \---Supporting Information | FigS11_DSC_DLM.1.1_isothermal215_heatto230.xls | FigS18_DSC_DLM.1.2_poststrain.xls | FigS18_DSC_DLM.1.2_prestrain.xls | FigS9_DSC_DLM.1.1_precipitated.xls | FigS9_DSC_DLM.1.1_press215.xls | FigS9_DSC_DLM.1.1_press230.xls | +---Raw_NMR | FigS1_NMR_LM4.zip | FigS1_NMR_P4MCL_macroinitiator.zip | FigS2_NMR_DLM_0min.zip | FigS2_NMR_DLM_60min.zip | +---Raw_SAXS | +---Fig3_FigS4-FigS8_SAXS_Blank | | 100C.txt | | 120C.txt | | 140C.txt | | 160C.txt | | 170C.txt | | 180C.txt | | 190C.txt | | 200C.txt | | 210C.txt | | 220C.txt | | 230C.txt | | 240C.txt | | 25C.txt | | 40C.txt | | 60C.txt | | 80C.txt | | | +---Fig3_FigS4-FigS8_SAXS_DLM.1.1 | | 100C.txt | | 120C.txt | | 140C.txt | | 160C.txt | | 170C.txt | | 180C.txt | | 190C.txt | | 200C.txt | | 210C.txt | | 220C.txt | | 230C.txt | | 240C.txt | | 25C.txt | | 40C.txt | | 60C.txt | | 80C.txt | | | +---Fig3_FigS4-FigS8_SAXS_DLM.1.2 | | 100C.txt | | 120C.txt | | 140C.txt | | 160C.txt | | 170C.txt | | 180C.txt | | 190C.txt | | 200C.txt | | 210C.txt | | 220C.txt | | 230C.txt | | 240C.txt | | 25C.txt | | 40C.txt | | 60C.txt | | 80C.txt | | | +---Fig3_FigS4-FigS8_SAXS_DLM.2.1 | | 100C.txt | | 120C.txt | | 140C.txt | | 160C.txt | | 170C.txt | | 180C.txt | | 190C.txt | | 200C.txt | | 210C.txt | | 220C.txt | | 230C.txt | | 240C.txt | | 25C.txt | | 40C.txt | | 60C.txt | | 80C.txt | | | +---Fig3_FigS4-FigS8_SAXS_DLM.3.1 | | 100C.txt | | 120C.txt | | 140C.txt | | 160C.txt | | 170C.txt | | 180C.txt | | 190C.txt | | 200C.txt | | 210C.txt | | 220C.txt | | 230C.txt | | 240C.txt | | 25C.txt | | 40C.txt | | 60C.txt | | 80C.txt | | | \---Fig3_FigS4-FigS8_SAXS_LM.0.1 | 100C.txt | 120C.txt | 140C.txt | 160C.txt | 170C.txt | 180C.txt | 190C.txt | 200C.txt | 210C.txt | 220C.txt | 230C.txt | 240C.txt | 25C.txt | 40C.txt | 60C.txt | 80C.txt | +---Raw_SEC | FigS3_SEC_DLM.1.1.xlsx | FigS3_SEC_LMcore.xlsx | +---Raw_SRA | Fig4_SRA_DLM.1.1_40C.xls | Fig4_SRA_DLM.1.1_50C.xls | Fig4_SRA_DLM.1.1_60C.xls | Fig4_SRA_DLM.1.1_70C.xls | Fig4_SRA_DLM.1.2_0C.xls | Fig4_SRA_DLM.1.2_120C.xlsx | Fig4_SRA_DLM.1.2_40C.xls | Fig4_SRA_DLM.1.2_50C.xls | Fig4_SRA_DLM.1.2_60C.xls | Fig4_SRA_DLM.1.2_70C.xls | Fig4_SRA_DLM.2.1_40C.xls | Fig4_SRA_DLM.2.1_50C.xls | Fig4_SRA_DLM.2.1_60C.xls | Fig4_SRA_DLM.2.1_70C.xls | Fig4_SRA_DLM.3.1_40C.xls | Fig4_SRA_DLM.3.1_50C.xls | Fig4_SRA_DLM.3.1_60C.xls | Fig4_SRA_DLM.3.1_70C.xls | Fig4_SRA_LM.0.1_0C.xls | Fig4_SRA_LM.0.1_40C.xls | Fig4_SRA_LM.0.1_50C.xls | Fig4_SRA_LM.0.1_60C.xls | +---Raw_Tensile | FigS21_Tensile_DLM.1.1_stress.strain.csv | FigS21_Tensile_DLM.1.2_stress.strain.csv | FigS21_Tensile_DLM.2.1_stress.strain.csv | FigS21_Tensile_DLM.3.1_stress.strain.xlsx | FigS21_Tensile_LM.0.1_stress.strain.csv | \---Raw_WAXS +---Fig3_FigS13-FigS17_WAXS_Blank | 100C.txt | 120C.txt | 140C.txt | 160C.txt | 170C.txt | 180C.txt | 190C.txt | 200C.txt | 210C.txt | 220C.txt | 230C.txt | 240C.txt | 25C.txt | 40C.txt | 60C.txt | 80C.txt | +---Fig3_FigS13-FigS17_WAXS_DLM.1.1 | 100C.txt | 120C.txt | 140C.txt | 160C.txt | 170C.txt | 180C.txt | 190C.txt | 200C.txt | 210C.txt | 220C.txt | 230C.txt | 240C.txt | 25C.txt | 40C.txt | 60C.txt | 80C.txt | +---Fig3_FigS13-FigS17_WAXS_DLM.1.2 | 100C.txt | 120C.txt | 140C.txt | 160C.txt | 170C.txt | 180C.txt | 190C.txt | 200C.txt | 210C.txt | 220C.txt | 230C.txt | 240C.txt | 25C.txt | 40C.txt | 60C.txt | 80C.txt | +---Fig3_FigS13-FigS17_WAXS_DLM.2.1 | 100C.txt | 120C.txt | 140C.txt | 160C.txt | 170C.txt | 180C.txt | 190C.txt | 200C.txt | 210C.txt | 220C.txt | 230C.txt | 240C.txt | 25C.txt | 40C.txt | 60C.txt | 80C.txt | +---Fig3_FigS13-FigS17_WAXS_DLM.3.1 | 100C.txt | 120C.txt | 140C.txt | 160C.txt | 170C.txt | 180C.txt | 190C.txt | 200C.txt | 210C.txt | 220C.txt | 230C.txt | 240C.txt | 25C.txt | 40C.txt | 60C.txt | 80C.txt | \---Fig3_FigS13-FigS17_WAXS_LM.0.1 100C.txt 120C.txt 140C.txt 160C.txt 170C.txt 180C.txt 190C.txt 200C.txt 210C.txt 220C.txt 230C.txt 240C.txt 25C.txt 40C.txt 60C.txt 80C.txt